“To be the leading provider of testing, commissioning, and engineering services in the electrical power industry, recognized for our innovation, quality, and commitment to safety.”
Company profile
Technical certainty, built in the field.
Electrical testing, commissioning and engineering solutions for critical power infrastructure.
Who we are
Committed to reliable power systems.
Al Beta Innovate Technical Services SPC, also known as Al Beta or ABITS, specialises in ensuring the highest standards of performance, safety and reliability in the electrical power industry.
We support grid stations, power plants and distribution equipment with engineering-led testing and commissioning. Our team brings regional GCC experience and a shared commitment to your electrical system's reliability and safety.
“Our mission is to deliver superior testing, commissioning, and engineering solutions that ensure the highest standards of performance, safety, and reliability for our clients' power systems.”
Empowering Excellence, Ensuring Safety—in every procedure, measurement and handover.
Core values
How we work.
Integrity
We act with honesty and transparency in every decision and record.
Safety first
We place people, assets and safe systems of work before all else.
Excellence
We pursue quality through discipline and continuous improvement.
Customer focus
We listen closely and shape our support around project needs.
Reliability
We do what we commit to and produce dependable results.
Investment in people
We strengthen capability through learning, mentoring and field experience.
Complete service scope
12 specialist service lines.
Practical scope written around the tests, checks and evidence required for a controlled handover.
Testing & Commissioning
We commission electrical assets across grid stations, power plants and distribution networks through disciplined test procedures and functional verification. Every activity is recorded against approved drawings, settings and acceptance criteria before energisation.
- SAT/FAT support and approved test documentation
- CT ratio, polarity and magnetisation curve testing
- VT ratio, polarity and phasing verification
- Secondary injection and end-to-end functional checks
- Interlock, trip matrix and protection loop verification
- Punch-list close-out and energisation support
Protection Relays
Protection schemes are configured and tested across relay families using approved coordination studies and setting files. We verify the complete chain from measured quantity through relay logic to the final trip output.
- Relay configuration and settings verification
- Secondary injection of current and voltage quantities
- Distance, differential and overcurrent element testing
- Binary input, output and programmable logic checks
- Trip matrix and breaker-failure scheme verification
- Functional loop and disturbance-record checks
Switchgear & Switchyards
Outdoor switchyards and switchgear up to 220 kV are tested for mechanical condition, insulation integrity and dependable operation. Results are correlated with manufacturer limits and commissioning baselines.
- Contact resistance measurement in micro-ohms
- Circuit-breaker timing and travel analysis
- Insulation resistance and polarisation index (PI)
- CT and VT primary equipment checks
- Local, remote and interlock functional tests
- Close/trip coil and anti-pumping verification
Transformers
Auto-transformers and power distribution transformers receive a complete electrical test suite before energisation. Measurements establish winding condition, transformation accuracy and correct phase relationship.
- Transformer turns ratio and vector-group verification
- Winding resistance on all tap positions
- Insulation resistance and PI measurements
- Magnetic balance and magnetising-current tests
- Bushing CT ratio and polarity checks
- OLTC operation, alarms and trip functional checks
Capacitor Banks & Surge Arresters
Reactive compensation and overvoltage protection equipment are inspected and tested as complete assemblies. We verify individual elements, protection interfaces and safe staged operation.
- Capacitance and phase-balance measurements
- Insulation resistance of bank and support insulation
- Discharge resistor and unbalance protection checks
- Surge arrester insulation and leakage-current checks
- Switching sequence and interlock verification
- Protection alarm and trip functional tests
GIS Equipment
Gas-insulated switchgear up to 400 kV is commissioned with close control of gas condition, primary-circuit integrity and operating sequences. Test records support safe handover of every bay and interface.
- SF6 gas purity, moisture and decomposition checks
- Main-circuit contact resistance in micro-ohms
- High-voltage withstand test support
- Breaker timing and travel analysis
- CT/VT ratio, polarity and phasing verification
- Bay interlock, alarm and trip matrix checks
Engineering Services
Protection and control engineering translates system requirements into safe, coordinated settings and executable schemes. Reviews focus on selectivity, fault duty and buildable control logic.
- Protection relay setting calculations
- Short-circuit and fault-level calculations
- Control schematic and logic review
- Protection coordination and grading checks
- Trip matrix and cause-and-effect review
- As-built drawing and setting-file verification
Cable Management
Control cable installation is managed from route preparation through termination and final loop proving. Identification, segregation and workmanship are checked at each stage.
- Control cable laying and dressing
- Cable trench preparation and route checks
- Glanding, ferruling and termination
- Continuity and insulation resistance testing
- Core identification against cable schedules
- Point-to-point and functional loop checks
Battery Systems
Station batteries and chargers are tested as the dependable DC source behind protection, control and emergency functions. We validate capacity, charger behaviour and distribution integrity.
- Battery bank voltage and cell condition checks
- Capacity and discharge testing
- Charger float, boost and current-limit checks
- DC earth-fault alarm verification
- Battery and charger changeover tests
- DC distribution polarity and functional checks
Motors & Generators
Rotating electrical machines are assessed before first run and during commissioning for insulation condition and correct protection response. Electrical findings are integrated with operational permissives.
- Insulation resistance and PI measurements
- Winding resistance and phase-balance checks
- CT ratio, polarity and protection circuit checks
- Motor protection secondary injection
- Space-heater and temperature-sensor checks
- Start permissive, trip and rotation verification
Control Panels
Existing control panels are refurbished and modified to restore dependable service or accommodate revised schemes. Work is completed against controlled drawings followed by systematic circuit proving.
- Panel wiring modification and refurbishment
- Component replacement and labelling
- Continuity and point-to-point verification
- Control voltage and polarity checks
- Functional loop and interlock checks
- Red-line mark-up and as-built support
Partial Discharge Solutions
Partial discharge activity is detected and assessed to identify developing insulation defects before failure. Findings are documented with practical mitigation and follow-up recommendations.
- Online and offline partial discharge surveys
- Signal capture and noise discrimination
- Pattern analysis and defect classification
- Location support for suspect discharge sources
- Baseline trending and comparative assessment
- Mitigation guidance and post-repair verification
Test resources
In-house test equipment.
Instrument availability supports primary, secondary and diagnostic testing across the commissioning programme.
| Equipment | Qty | Application |
|---|---|---|
| OMICRON CMC 356 | 3 | Protection relay testing kit |
| OMICRON CPC 100 | 2 | Primary equipment testing kit |
| OMICRON CT Analyser | 1 | Current transformer — voltage method |
| Megger MIT 515 (5 kV) | 2 | Insulation tester |
| VLF B2 Electronics | 1 | Variable low frequency test kit |
| Hipotronics HIPOT | 1 | High voltage test for GIS |
| DV Power RMO-H (300 A) | 2 | Micro-ohm meter |
| SCOPE MXP+ | 1 | Circuit breaker analyser |
| Fluke digital multimeters | 5 | Secondary measurement |
| Fluke digital clamp meters | 5 | Secondary measurement |
Our team
Experience where it matters.
Commissioning specialists with hands-on experience across substations, power plants and industrial facilities.
Stenny Raj
Manager18+ years in T&C of all electrical equipment in power plants, substations and industries
Mariselvam
T&C Engineer12+ years in T&C of all electrical equipment in power plants, substations and industries
Senthilnathan
T&C Engineer11+ years in safety identification and mitigation
Arunkumar
T&C Engineer10+ years in T&C of all electrical equipment in power plants, substations and industries
Hariselvam
T&C Engineer09+ years in safety identification and mitigation
Santhosh Rajah
T&C Engineer09+ years in safety identification and mitigation
HSE & quality
Safety is part of the method.
We plan work around approved procedures, verified isolation, calibrated instrumentation and clear responsibilities. Testing is documented, reviewed and closed against applicable project requirements.
Quality is sustained through accurate records, drawing and setting verification, disciplined punch-list management and continuous learning from field activity.